Re: [atlas] RIPE Atlas Virtual Anchor Registration for DCS1 (sg-sin-as37989)
Hi, I am trying to install the virtual anchor of the ISO. Unfortunately, my experience with Unix went directly from Sun to Debian in the late 90s, so I am not sure of the intricacies of RHEL anaconda What (and in what format) do I answer here: 1. IPv4 address: 203.123.48.20 2. IPv4 Netmask: I tried 255.255.255.224, which it seemed not to like, so I tried /27, and then 27. 3. IPv4 gateway: 203.123.48.6 4. IPv6 address: 2405:fc00::20 (it keeps failing, should I enclose this in [] )? 5. IPv4 Netmask: I tried /64, and then 64 6. IPv4 gateway: 2405:fc00::6 Now it fails with: <snip>freedektop.NetworkManager.Settings.Connection.MissingPropert: ipv4.addresses: this propery cannot be empty for 'method=manual' And how do I backspace in the installer? Neither BKSP nor ^H seem to work. Thanks, -- Sanjeev Gupta +65 98551208 http://www.linkedin.com/in/ghane On Thu, 27 Jul 2023 at 22:22, RIPE Atlas <no-reply@ripe.net> wrote:
Dear Sanjeev Gupta,
Thank you for registering the technical information for your RIPE Atlas virtual anchor!
Your FQDN is: sg-sin-as37989.anchors.atlas.ripe.net
You will need now to setup the Virtual Machine according to these instructions: (https://atlas.ripe.net/docs/anchor-installation-vm/).
It is important that once you have setup the virtual machine, you log in to your RIPE Atlas account, go to the "My Atlas" menu and then "Anchors", and check the boxes “Software is installed” and "Anchor is connected to the network" so we are notified and can begin the tests. Please note that your anchor will not be fully activated until we have finished these internal tests.
We will notify you once we have finished testing and your virtual anchor is ready to use.
If you have any questions, please do not hesitate to contact us at atlas@ripe.net
You registered the following details:
IPv4 address: 203.123.48.20 IPv4 ASN: 37989
IPv6 address: 2405:fc00::20 IPv6 ASN: 37989
Kind regards,
RIPE Atlas Team
Hi Sanjeev, Your question is specific to your anchor installation, and you also sent it to the RIPE NCC's ticket system, so one of my colleagues will follow up with you via the ticket system. Regards, Anand Buddhdev RIPE NCC On 27/07/2023 17:22, Sanjeev Gupta wrote:
Hi,
I am trying to install the virtual anchor of the ISO. Unfortunately, my experience with Unix went directly from Sun to Debian in the late 90s, so I am not sure of the intricacies of RHEL anaconda
What (and in what format) do I answer here:
1. IPv4 address: 203.123.48.20 2. IPv4 Netmask: I tried 255.255.255.224, which it seemed not to like, so I tried /27, and then 27. 3. IPv4 gateway: 203.123.48.6 4. IPv6 address: 2405:fc00::20 (it keeps failing, should I enclose this in [] )? 5. IPv4 Netmask: I tried /64, and then 64 6. IPv4 gateway: 2405:fc00::6
Now it fails with: <snip>freedektop.NetworkManager.Settings.Connection.MissingPropert: ipv4.addresses: this propery cannot be empty for 'method=manual'
And how do I backspace in the installer? Neither BKSP nor ^H seem to work.
Thanks,
participants (2)
-
Anand Buddhdev -
Sanjeev Gupta