More information: it isn't showing up on my DHCP server. When plugged in it shows the link light, blinks actiti for seven seconds, both lights turn off, and then this sequence repeats forever. On Fri, Aug 23, 2024 at 10:37 AM Phillip Remaker <remaker@gmail.com> wrote:

Thanks for replying. Yes, it is still happening.

On Tue, Aug 6, 2024 at 7:32 AM Michel Stam <mstam@ripe.net> wrote:

...

Hello Philip,

Can you tell me whether your problem persists right now? We’ve had some minor issues in the infra that may have affected your probe.

Regards,

Michel

On 3 Aug 2024, at 16:44, Phillip Remaker <remaker@gmail.com> wrote:

Hello!

I have an 11+ year old v2 probe

Seems to be in a reboot loop. Starts up, all LEDs go blank, and it repeats.

Any diagnostics I can do? Any repairs?

https://atlas.ripe.net/probes/4111/#tab-network ----- To unsubscribe from this mailing list or change your subscription options, please visit: https://mailman.ripe.net/mailman3/lists/ripe-atlas.ripe.net/ As we have migrated to Mailman 3, you will need to create an account with the email matching your subscription before you can change your settings. More details at: https://www.ripe.net/membership/mail/mailman-3-migration/

I have left my problem connected (im parallel) with a working one) to see if it ever comes up. On Sat, Aug 24, 2024 at 10:34 AM Mike via ripe-atlas <ripe-atlas@ripe.net> wrote:

On 8/23/2024 1:37 PM, Phillip Remaker wrote:

...

Thanks for replying. Yes, it is still happening.

[snip]

It has recurred here as well (probe #10553).

The probe has been disconnected for the past 11 hours.

----- To unsubscribe from this mailing list or change your subscription options, please visit: https://mailman.ripe.net/mailman3/lists/ripe-atlas.ripe.net/ As we have migrated to Mailman 3, you will need to create an account with the email matching your subscription before you can change your settings. More details at: https://www.ripe.net/membership/mail/mailman-3-migration/

Hi! I have the same issue as you. My v2 probe #4019 stopped working last June: FIRST CONNECTED 2012-12-07 08:56:15 (UTC) LAST CONNECTED 2025-06-24 16:50:00 (UTC) TOTAL UPTIME 12y 8d 21h 52m 4s The probe is not requesting IPv4 addresses from my DHCP server, but is still sending some IPv6 requests, then rebooting. I found the pinout of the Lantronix XPP1003000-02R Embedded Module, and it has a UART pins. I think I can connect to these pins and check what's happening on the probe's Serial Console. The next step is to remove the protective shield and check the type of flash. On Thu, Nov 28, 2024 at 9:16 AM Phillip Remaker <remaker@gmail.com> wrote:

I thought I would ask one more time before I write off the probe. I got an automated email from the system asking me to reconnect the probe. Is there any other physical diagnostic I can do to a constantly rebooting V2 probe? I am happy to crack it open, and even have a soldering iron. However, at its age, I’m suspecting that the flash chip has failed.

On Sat, Aug 3, 2024 at 7:44 AM Phillip Remaker <remaker@gmail.com> wrote:

...

Hello!

I have an 11+ year old v2 probe

Seems to be in a reboot loop. Starts up, all LEDs go blank, and it repeats.

Any diagnostics I can do? Any repairs?

https://atlas.ripe.net/probes/4111/#tab-network

----- To unsubscribe from this mailing list or change your subscription options, please visit: https://mailman.ripe.net/mailman3/lists/ripe-atlas.ripe.net/ As we have migrated to Mailman 3, you will need to create an account with the email matching your subscription before you can change your settings. More details at: https://www.ripe.net/membership/mail/mailman-3-migration/